Just How to Install a Bath Tub Yourself
Just How to Install a Bath Tub Yourself
Blog Article
We've stumbled on this post about Installing A Bathtub down the page on the internet and felt it made sense to talk about it with you on this site.
Setting up a bath tub isn't specifically rocket science, but it does require solid plumbing, carpentry, as well as occasionally, tiling abilities. Changing an old bath tub with a new one is also a moderately challenging job. If the old tub is readily available, the job can relocate immediately; if you need to open up a wall to remove the old bathtub and also place the brand-new bath tub, the task is much harder. In either situation, the job is within a house handyman's abilities, although you will certainly require an assistant to vacate the old bathtub and also embeded in the brand-new one. Make certain you have actually certified on your own for the work and also fit attempting it. Rather than hiring a service provider to take control of a halfway-completed task, it is better to consider employing one before you begin. Chances are you may require a specialist plumber to make tube links.
This write-up will certainly assist you set up a new bathtub in your bathroom if you have actually currently gotten a brand-new tub and don't require to change the arrangement of your previous water supply pipelines.
Your devices as well as material checklist should consist of the following:
Removing Old Touches
If you need to replace old faucets with brand-new ones as a part of your installation, then the first thing you need to do is detach the water. After doing so, activate the faucets to drain pipes any type of water remaining in the system. The process of getting rid of the existing faucets can be rather problematic due to the limited gain access to that is typically the case.
Make use of a container wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipes to the taps. Have a towel prepared for the remaining water that will certainly come from the pipelines. When the supply pipes have been removed, make use of the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the single taps from transforming during this process. As soon as the taps have actually been eliminated, the holes in the bath/basin will certainly have to be cleaned of any old securing compound.
Prior to proceeding to fit the brand-new taps, contrast the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.
Fitting New Touches
If the tails of the new faucets are plastic, then you will certainly need a plastic port to prevent damages to the string. One end of the port fits on the plastic tail of the faucet as well as the various other end offers a link to the existent supply pipelines.
If you need to fit a monobloc, then you will certainly require lowering couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next off, position the faucet in the mounting hole in the bath/basin making certain that the washers are in area between the tap as well as the sink. Secure the faucet in place with the maker provided backnut. When the tap is safely in position, the supply pipes can be attached to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with typical faucet adapters. The former type needs to be connected to the tap finishes initially, tightening only by hand. The supply pipelines can later on be attached to the other end. Tighten up both ends with a spanner after both ends have been linked.
Installing the Tub
Making use of the two wooden boards under its feet, position the bathtub in the needed placement. The wooden boards are valuable in evenly spreading out the weight of the bathtub over the area of the boards rather than concentrating all the weight onto 4 tiny points.
The next goal is to make sure that the bath tub is leveled all round. This can be attained by checking the spirit level as well as readjusting the feet on the bath tub until the spirit level checks out level.
To set up faucets, fit all-time low of the outermost adaptable tap connector to the suitable supply pipe by making a compression join; after that do the exact same for the various other faucet.
Activate the water and also examine all joints and also new pipework for leaks and tighten them if necessary. Fill the bathtub and also inspect the overflow outlet as well as the typical outlet for leaks.
Lastly, repair the bath paneling as explained in the producer's instruction manual. Tiling and sealing around the bathtub should wait till the tub has actually been made use of at least once as this will settle it into its final setting.
Getting ready for the Setup
First of all, the sustaining framework provided with the bathroom must be fitted (if needed) according to the maker's directions. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is very important to make certain that if the tap features a plastic washing machine, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is also sensible to fit a sustaining plate under the faucets device to stop stress on the tub.
Fit the versatile tap connectors to the bottom of the two taps utilizing 2 nuts and olives (sometimes provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet via the hole in the bathroom. Use the nut provided by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bath. See to it you utilize all of the provided washers.
Attach the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bath must now prepare to be fitted in its final setting.
Tiling Around the Bathtub
In the location where the bath fulfills the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is very important as the fitting can relocate enough to fracture a rigid seal, creating the water to permeate the wall surface between the bathroom and the tiling, bring about problems with wetness as well as feasible leaks to the ceiling listed below.
You can choose from a range of coloured sealers to blend in your components and installations. They are sold in tubes as well as cartridges, and also are capable of securing gaps as much as a size of 3mm (1/8 inch). If you have a larger space to fill, you can fill it with spins of soaked paper or soft rope. Bear in mind to always fill up the bath tub with water before securing, to permit the movement experienced when the bathtub remains in use. The sealer can fracture relatively very early if you do not take into account this motion prior to sealing.
Additionally, ceramic coving or quadrant floor tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are additionally easily offered on the marketplace. It is advisable to fit the tiles utilizing waterproof or waterproof adhesive as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
:max_bytes(150000):strip_icc()/convert-tub-to-shower-4156975-05-db9a69eb718545759045e6e39b4cfacf.jpg)
I stumbled upon that review about How to Install a Bathtub Yourself when doing a lookup on the search engines. Sharing is caring. Helping others is fun. Thank you for your time. Visit again soon.
Schedule Appointment Now
Report this page